data sheet no. pd 10035 rev k series PVG612PBF microelectronic power ic hexfet ? power mosfet photovoltaic relay single pole, normally open, 0-60v, 1.0a ac/ 2.0 a dc general description the pvg612 series photovoltaic relay is a sin gle- pole, normally open solid-state re lay that can replace electromechani cal re lays in many applications. it util- izes international rectiiers proprietary hexfet po wer mosfet as the output switch, driven by an inte grated circuit photovoltaic gen erator of novel constructi on. the output switch is con trolled by radiation from a gaalas light emit ting diode (led) which is optically isolated from the photovol taic generator. these units exceed the performance capabilities of electromechanical relays in operating life, sensitivity, stability of on-resistance, miniaturization, insens itivity to magnetic ields and ruggedess. the compact pvg612 is particularly suited for isolated switching of hi gh currents from 12 to 48 volt ac or dc power sources. series pvg612 relays are packaged in a 6-pin, molded dip package with either thru-hole or surface mount (gull-wing) termi nals. it is avail able in standard plastic ship ping tubes or on tape-and-reel. please refer to part identiica tion in formation opposite. features ? bounce-free operation ? high load current capacity ? high off-state resistance ? linear ac/dc operation ? 4,000 v rms i/o isolation ? solid-state reliability ? ul recognized ? esd tolerance: 4000v human body model 500v machine model applications ? programmable logic controllers ? computers and peripheral devices ? audio equipment ? power supplies and power distribution ? control of displays and indicators ? industrial automation part identiication PVG612PBF thru-hole pvg612spbf surface-mount pvg612s-tpbf surface-mount, tape and reel (hexfet is the registered trademark for international rectiier power mosfets) www.irf.com 1 downloaded from: http:///
series PVG612PBF www.irf.com 2 input characteristics limits units minimum control current (see igure 1) 5.0 ma maximum control current for off-state resistance @ t a = +25c 0.4 ma control current range (caution: current limit input led, see igure 6) 5.0 to 25 ma maximum reverse voltage 6.0 v output characteristics limits units operating voltage range 0 to 60 v (dc or ac peak) maximum load current @ t a = +40c, 10ma control (see igure 1) a connection 1.0 a (ac or dc) b connection 1.5 a (dc) c connection 2.0 a (dc) maximum pulsed load current @ t a =+25c (100 ms @ 10% duty cycle) a connection 2.4a (ac or dc) maximum on-state resistance @t a =+25c for 1a pulsed load, 10ma control (see igure 4) a connection 500 m b connection 250 m c connection 150 m minimum off-state resistance @t a =+25c, 48v (see igure 5) 10 8 maximum turn-on time @t a =+25c (see igure 7) for 500ma, 50 v dc load, 10ma control 2.0 ms maximum turn-off time @t a =+25c (see igure 7) for 500ma, 50 v dc load, 10ma control 0.5 ms maximum output capacitance @ 50v dc (see igure 2) 130 pf electrical speciications (-40c t a +85c unless otherwise speciied ) general characteristics limits units minimum dielectric strength, input-output 4000 v rms minimum insulation resistance, input-output, @t a =+25c, 50%rh, 100v dc 10 12 maximum capacitance, input-output 1.0 pf maximum pin soldering temperature (10 seconds maximum) +260 ambient temperature range: operating -40 to +85 c storage -40 to +100 connection diagrams international rectiier does not recommend the use o f this product in aerospace, avionics, military or life support applications. users of this international rectiier product in such applications assume all risks of such use and i ndemnify international rectiier against all damages resulting from such use. downloaded from: http:///
series PVG612PBF www.irf.com 3 max. load current (a) ambient temperature (deg. c) 20 40 60 80 10 0 0 0.25 0.50 0 1.00 1.25 0.75 i led 10 ma 5 ma = 'a' connection figure 1. current derating curves* figure 2. typical output capacitance typical capacitance (pf) vdd, drain to drain voltage (v) 0 15 30 45 6 0 450 300 150 0 600 'a' connection load current (a) @25c, p ulsed 10 ma control -0.1 -0.2 -0.3 -0.4 -0.5 0.50 1.25 1.00 0.25 0.75 -0.25 -1.25 -1.00 -0.75 -0.50 0. 5 0.4 0.3 0.2 0.1 connec tion 'a' voltage drop (vdd) rd-on (normalized to 25 deg. c) ambient temperature (deg. c) 2.5 2.0 1.5 1.0 0.5 0 -50 -25 0 25 50 75 100 12 5 10 ma control = 500 ma d i 'a' connec tion figure 3. linearity characteristics figure 4. typical normalized on-resistance * derating of b and c connection at +85c will be 70% of that speciied at +40c and is linear from +40c to +85c. downloaded from: http:///
series PVG612PBF www.irf.com 4 led current (ma) delay time (microsec onds) 50 100 200 500 20 1000 200 0 20 10 5 3 t off t dly t on 90% 10% i i led d t dly t on t off figure 7. typical delay times figure 8. delay time deinitions ambient temperature (deg. c) -35 -15 5 25 45 65 85 10 5 100 30 10 3.0 1.0 0.3 0.1 i d-off 25 deg. c / i d-off input current (ma) led forward voltage drop (volts dc) 16 20 12 84 0 0.5 1.0 1.5 2. 0 0 not exc eed ed t y p i c a l caution: provid e c urrent limiting so that 25 ma maximum stea dy- state co ntrol c urrent rating is m i n . d e v i c e a n d + 8 5 d e g . c l i m i t m a x . d e v i c e a n d - 4 0 d e g . c l i m i t figure 5. typical normalized off-state leakage figure 6. input characteristics (current controlled) downloaded from: http:///
series PVG612PBF www.irf.com 5 ir world headquarters: 233 kansas st., el segundo, california 90245 tel: (310) 252-7105 data and speciications subject to change without notice. 2/2008 01-2008 01 case outlines 01-2009 01 downloaded from: http:///
|
